MOZA RACING AS011 Force Feedback Yoke Base

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please visit our customer support page: www.alza.cz/EN/kontakt.

Product Features

• MCLS Force Feedback Technology
• 9 Nm Roll Force and 200 N Pitch Force
• Aluminum Quick Release
• Programmable Switch Panel
• 150 mm Long Pitch Travel
• High-Resolution Encoder

Dimensions and Mounting Parameters

• Dimensions (in mm):
• Width: 503.4
• Height: 111.28
• Depth: 243
• Side Mount: 4x M5 screws
• Bottom Mount Pattern: 4x M6 central holes, 4x Ø6.5 outer holes

Connection Ports

User Guide

Securing the Yoke

• Rotate the D-shaped head on the MOZA Force Feedback Yoke Base as shown

Press and hold the Quick Release handle on the back of the MFY Yoke Handle, then align it with the connecting rod.

Once inserted, release the handle and gently wiggle the yoke to ensure it’s firmly attached.

• Power on the MOZA yoke base. The lights on the MFY Yoke Handle should illuminate.
• If not, check that the handle is properly attached or verify brightness settings in the MOZA Cockpit software.

Securing the Yoke Base

• Desktop Clamping (requires optional desk clamp)
• Attach the included spacer pads to the outer sides of the yoke base.
• Secure the desk clamp to the protruding sections.
• Tighten the star-shaped knob until the base is firmly clamped to the desk

Simulator Mounting The base can also be mounted to simulator cockpits using the screw holes underneath.

• Connecting to PC
• Connect the power cable to the MOZA AY210 yoke base and plug it into a 220V outlet.
• Short-press the power button to turn it on (long press to turn off). The power light will flash when successfully connected.

If connected properly, the power LED will remain on and the control panel will light up.

Software Introduction
The main dashboard in MOZA Cockpit shows the operational status of all connected devices, including the base, yoke, throttle, and rudder pedals. It also allows for quick game launch shortcuts.

Base Features
Cogging Torque Calibration Press the calibration button in the interface to optimize cogging torque and balance of the yoke handle. The process may take a few moments—wait for the progress bar to complete before performing other actions. Important: Do not touch the yoke handle during calibration to ensure accuracy.
Base Front Panel Backlight Adjustment

• The AY210 base offers two backlight brightness modes:
• Manual Mode: Adjust the brightness level (0–15) using the slider in MOZA Cockpit. Level 0 turns the backlight off.
• Telemetry Mode: The backlight brightness synchronizes automatically with the in-game cockpit lighting via telemetry data.
• Landing Gear Light
• The landing gear light is positioned in the top-right corner of the front panel and supports three color modes: Off, Red, Green.
• Two modes for brightness control:
• Manual Mode: Brightness is adjusted via the gear light slider (levels 0–15).
• Telemetry Mode: Brightness is synced with in-game telemetry.
• Landing Gear Status Lighting
• Gear Up Position You can assign a light color to indicate when the gear is fully retracted.
• Off: Light is turned off when gear is up
• Red: Light is red when gear is retracted
• Unlocked State This shows when gear is transitioning or unlocked.
• Off: Light stays off during transition
• Red: Light stays red during transition

Flap Switch Long-Press Timeout
Use the “Flap Switch Long-press Timeout” slider to define how long the flap switch must be held to trigger a long-press function. Example: With a 2-second setting, holding the switch up or down for 2 seconds will activate a long-press action.
Base Force Feedback Settings
Click the base icon in the sidebar of MOZA Cockpit to open the force feedback settings.

• Here you can:
• Adjust mechanical and dynamic FFB parameters
• Access multiple tabs like Basic Settings, Expert Settings, Dynamic FFB, and Telemetry
• Save custom profiles using the Preset Management system

Base Reset

• If you encounter issues with force feedback or axis calibration:
• Press the Reset Base button in the software
• If the issue continues, contact MOZA support
• Allow a few moments for the reset to finish

Specifications

• Precautions
• Do not expose the device to liquids or moisture to avoid fire or electric shock.
• Avoid using the device in direct sunlight.
• Do not use MOZA flight sim gear with MOZA racing gear.
• Recommended indoor temperature: 5°C to 35°C.
• Take regular breaks and monitor your gaming time.
• Not suitable for children under 6 years. Small parts may pose a choking hazard.
• Children under 13 must be supervised.
• Do not disassemble the product. Doing so voids warranty.
• Only use the supplied power adapter.
• Repairs or replacements must be done through authorized service centers.
• Never use a third-party or mismatched power supply.
• Use only AC power from a standard wall outlet.
• Keep the device away from heat sources.
• Unplug the device if not used for a long time.
• If something seems wrong, stop using it and contact support.
• Stay updated via the official website and MOZA’s social media for firmware and software updates

Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller directly, you must provide the original proof of purchase with the date of purchase.

• The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:
• Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
• Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
• Natural wear and aging of consumables or components during use (such as batteries, etc.).
• Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components

EU Declaration of Conformity
This product complies with the legal requirements of the European Union directive(s).
WEEE
This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19/EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations

Documents / Resources

MOZA RACING AS011 Force Feedback Yoke Base [pdf] User Manual AS011, AS011 Force Feedback Yoke Base, Force Feedback Yoke Base, Feedback Yoke Base, Yoke Base

References

• User Manual